Valve cover coming off
- kneedragger80
-
Topic Author
- Offline
- User
-

Registered
- Posts: 42
- Thanks: 0
Valve cover coming off
29 Mar 2008 07:24
I'll soon be replacing the valve cover on a 1980 750E. The bike has 20K miles and is new to me. The original cover was powder coated and I don't have the time/patience to strip it or blast it.
While I have the cover off, is there anything I should be looking for or check while I have it open? Any adjustments or anything else I should address while I have the chance?
While I have the cover off, is there anything I should be looking for or check while I have it open? Any adjustments or anything else I should address while I have the chance?
80 KZ750E
84 GPZ1100
NY US
. . . I used to do a little but a little wouldn t do it so a little got more and more . . .
84 GPZ1100
NY US
. . . I used to do a little but a little wouldn t do it so a little got more and more . . .
Please Log in or Create an account to join the conversation.
- Mcdroid
-
- Offline
- Sustaining Member
-

Registered
- Gone Kwackers
- Posts: 6909
- Thanks: 530
Re: Valve cover coming off
29 Mar 2008 07:28
Always take the time to check valve shim clearances at opportunities like this...you should also consider replacing the valve cover gasket at these opportunities and be prepared to swap shims, if need be.
Michael
Victoria, Texas
1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A
Victoria, Texas
1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A
Please Log in or Create an account to join the conversation.
- ronjones
-
- Offline
- User
-

Registered
- Posts: 565
- Thanks: 5
Re: Valve cover coming off
29 Mar 2008 08:11
You might need to replace those end cap seals, along w/the gasket. I couldn't do my shim adjustment w/o removing my cams, so at that point, you're close to the valve seals.
'82 KZ750 CSR, M1 twin. Mac 2-1 exhaust, K&N pods, 17tooth drive sprocket, Mikuni BS-34 carbs w/#47.5 pilot jet and #125 main jet, Canadian XS650 needlejetjet needle, Wired George's coil mod.
Barrak, Nancy and Harry says: Welcome to the United Soviet States of America, Comrades
Barrak, Nancy and Harry says: Welcome to the United Soviet States of America, Comrades
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Valve cover coming off
29 Mar 2008 09:00
some good paint stripper will clean that right off with a carwash hose in no time.
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: Valve cover coming off
29 Mar 2008 15:55
Remove the cam chain tensioner first, and install it last.
KD9JUR
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Valve cover coming off
29 Mar 2008 18:50
Mcdroid wrote:
Considering the price of cover gaskets, you may want to buy some gasket material at pep Boys and use the old one for a pattern. The dealer wanted $80 for mine.
Always take the time to check valve shim clearances at opportunities like this...you should also consider replacing the valve cover gasket at these opportunities and be prepared to swap shims, if need be.
Considering the price of cover gaskets, you may want to buy some gasket material at pep Boys and use the old one for a pattern. The dealer wanted $80 for mine.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Valve cover coming off
29 Mar 2008 18:53
ronjones wrote:
Those things do like to leak. They aren't cheap to replace, I think mine were about $60 for a set. If they are not too bad, you can seal them by prying them out and cleaning them up and then setting them back in with good RTV sealant. I used the ultra high temp black stuff.You might need to replace those end cap seals, along w/the gasket.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- grandadbob
-
- Offline
- User
-

Registered
- Posts: 29
- Thanks: 0
Re: Valve cover coming off
30 Mar 2008 23:27 - 30 Mar 2008 23:30
As mentioned earlier remove cam tensioner firdt and replace last. Think about it.
This is a really top tip. Remember to fit alloy washer to cam tensioner cap on assembly. I forgot and sheared tensioner body at base of thread.
This is a really top tip. Remember to fit alloy washer to cam tensioner cap on assembly. I forgot and sheared tensioner body at base of thread.
'83 KZ550 C4 LTD
'06 VFR800 Vtec
'06 VFR800 Vtec
Last edit: 30 Mar 2008 23:30 by grandadbob.
Please Log in or Create an account to join the conversation.
- kneedragger80
-
Topic Author
- Offline
- User
-

Registered
- Posts: 42
- Thanks: 0
Re: Valve cover coming off
02 Apr 2008 05:21
Thanks for all the good info. I guess I have more work to do under the cover than I thought.
80 KZ750E
84 GPZ1100
NY US
. . . I used to do a little but a little wouldn t do it so a little got more and more . . .
84 GPZ1100
NY US
. . . I used to do a little but a little wouldn t do it so a little got more and more . . .
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
