calling all racers

  • mark1122
  • mark1122's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

calling all racers

30 Mar 2008 11:38
#203103
how close do the pistons need to be in regards to weight?is a 1 gram diff too much,1/10th gram?? for a kz street motor ,1327cc.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: calling all racers

30 Mar 2008 20:42
#203188
usually they are matched pretty close when you buy them as a setB)
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

  • Dirtybiker
  • Dirtybiker's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: calling all racers

30 Mar 2008 21:36
#203194
I was told too weigh the pistons rod caps and rod bolts together. 1 Gram is fine. Never add weight. shave off lettering rough edges too get the desired weight. I plan on doing just that as soon as my bottom end is done. And i buy a gram scale.

Scott

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: calling all racers

31 Mar 2008 09:17
#203253
on the 900-1000 motors the rods and crank are pressed together so you cant balance them that way.normally as long as the pistons are pretty close the 2 up-2 down setup of these motors does a good job of cancelling things out.B)
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

  • 77KZ650
  • 77KZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1397
  • Thanks: 7

Re: calling all racers

31 Mar 2008 10:24 - 31 Mar 2008 10:26
#203266
i think 1 tenth is best. less vibration. weigh the pistons with the pins in them
07 MDP Rookie of the Year
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH
Last edit: 31 Mar 2008 10:26 by 77KZ650.

Please Log in or Create an account to join the conversation.

  • BSKZ650
  • BSKZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 2061
  • Thanks: 14

Re: calling all racers

31 Mar 2008 11:43
#203292
I dont think the balance needs to be that close, we do try to get it as close as possible, but when you look at the function of the engine..... how much more oil was on piston assembly 1 than was on assembly 3 at that cycle after all oil does add wieght to the rotating assembly and it changes everytime it rotates,
get them close, but I think you will find them from the factory to be fine, dress any sharpe edges, check the ring gap, and make sure the bore is round and has a good cross hatch pattern.
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob

Please Log in or Create an account to join the conversation.

  • donthekawguy
  • donthekawguy's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1911
  • Thanks: 8

Re: calling all racers

01 Apr 2008 00:09 - 01 Apr 2008 00:11
#203443
On any motor I rebuild I make sure every piston assembly is as close as possible. It only takes a few minutes and gives me peice of mind. With the bike I weighed the pistons, rings and pins after fitting the rings to the cylinders. On the kids Acura last summer it was the rods, bearings, pins, and rings and pistons. Granted that was a spendy motor and he wanted to spend the extra time on it, but he gets to rev it to 9K without a worry. :S
Rathdrum Idaho
1971 Kawasaki g3ss
1972 Yamaha R5 350
1965 Suzuki Hillbilly
1964 Yamaha 125
Last edit: 01 Apr 2008 00:11 by donthekawguy. Reason: cuz

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: calling all racers

01 Apr 2008 10:35
#203530
thanks guys. my 1135cc wiesco's were out 4.5 grams . i had a vibration below 3000rpm. the mtc 1327cc's were out 1 gram. i took a page out of my last builders book. he had added a 2nd oil hole in the piston for the wrist pins. so i drilled a 2nd hole in each pistons wrist pin boss and through to the oposite side of the pin whole till i got the pistons all the same weight. less than 1 10th gram dif.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 77KZ650
  • 77KZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1397
  • Thanks: 7

Re: calling all racers

02 Apr 2008 18:43
#203846
mark1122 wrote:
thanks guys. my 1135cc wiesco's were out 4.5 grams . i had a vibration below 3000rpm. the mtc 1327cc's were out 1 gram. i took a page out of my last builders book. he had added a 2nd oil hole in the piston for the wrist pins. so i drilled a 2nd hole in each pistons wrist pin boss and through to the oposite side of the pin whole till i got the pistons all the same weight. less than 1 10th gram dif.

niceB)
ill be trying to get the JE's going into my 12r that close...extending the revlimiter is going to be tough on it, so i want it as smooth/balanced as possible:woohoo:
07 MDP Rookie of the Year
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum