Could use some timing help, New guy here....

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Could use some timing help, New guy here....

25 Oct 2011 22:37
#485359
Hello everyone, My name is Will. I just recently got a new toy...A fourwheeler with a Kz550 engine on it. It's a 98 yamaha 2wd wheeler that's more or less set up for drag racing. Well, I blew the head gasket the first afternoon I got it, or should say finished it off.

Well, for a quick fix I used some copper rtv sealant and that held till today when i got the real gasket in from the part place. Well, the other week when i did this I used a sharpie to mark a tooth on each cam. then when i put the cams back in I just lined the marks back up and wal lah, she started right up and ran perfectly fine. Well, obviously this trick did NOT work right today.
I turned it over by the crank bolt, a 9/16's i believe, but anyway turned it over slowly and could hear binding of the valves. But before i knew it they "popped" and the engine spun over just fine. Well, I just went ahead and checked and sure enough while installing that dang tensioner the cam chain must have turned a bit cause teh marks were no longer lining up at all.


Two question's, One i REALLY do not wanna tear into the head again as it took forever and cost me $90 for a head gasket! And I am worried if I take off the head again i will have to buy another one or it wont seal up right. Would you guys pull it again, or just see what happens once the timing is set right?

And two, What friggin marks do i use to set the cam timing? I hear of all these different marks like ex and 5z and even paid to down load a manual for the thing, btw it was completely wrong... i have NO TDC marks at all on teh crank or anywhere else that i can find. So i just put the engine at TDC and am hoping you guys can help me out.


I am guessing the Intake cam is the REAR cam since it's near the carbs, and teh Exhaust cam is toward the front of the engine correct? And one last thing, sorry... With the coils, I know one coil fire's off 1 and 4, and the other coil does 2, and 3. So as long as I keep those same specs I should be fine right? meaning use either coil for 2,3..and the other for 1,4..right?


I know this is alot of questions for a new member and thank you all for your help. i look forward to getting to know this forum!! BTW, of course here are a few pics.


Please Log in or Create an account to join the conversation.

  • P21
  • P21's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 471
  • Thanks: 34

Re: Could use some timing help, New guy here....

25 Oct 2011 22:55
#485364
welcome to the forum
do you know what year that motor is?
i am not familar with the kz550 motor
but the kz1000 motors have marks on the cam sprockets and at the points cover for firing and TDC marks
Kawasaki KZ 1000 Police (2002) P21

Please Log in or Create an account to join the conversation.

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Could use some timing help, New guy here....

25 Oct 2011 23:08
#485367
Honestly I have NO clue as to the year. It does NOT have a points style ign if that tells you anything. Sorry, wish i knew more. I am pretty handy and know how to use google pretty well, but frankly this engine just does not have too much info listed on it. Heck, it took me over two days looking to find the head gasket!

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Could use some timing help, New guy here....

25 Oct 2011 23:31
#485371
What's the engine serial? You might be able to figure out roughly the year from it.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Could use some timing help, New guy here....

26 Oct 2011 00:05
#485375
You should first download the service manual, then go to Loudhvx's web site for the 550.
home.comcast.net/~loudgpz/KZ5mnl.pdf
Here you will find some of the best info. Also you can go into "Filebase" at the top right corner of KZR. Lots of info there.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: Could use some timing help, New guy here....

26 Oct 2011 00:16 - 26 Oct 2011 00:22
#485377
There is more than you ever wanted to know about KZ550 cam timing on my website. Check my signature for the valve train warning. It has the details for cam timing.

There is a manual in my signature (as MotorHead linked to.)

The coil wires, originally, are numbered. As you sit on the bike, the cylinders are numbered left to right.

If you take apart the advancer, and/or wiring, it's easy to get the cylinder pairs swapped on the ignition.

The coil with the black primary wire fires 1 and 4. The coil with green primary wire will fire 2 and 3. The coils are interchangeable electrically, but the plug wires are different lengths. Obviously,the outer cylinders get the longer plug wires.

For cam timing, you use the "T" mark on the advancer mechanism to get the crank at TDC. My website illustrates where to set the cams.

Unfortunately, it sounds to me like the head will have to come off again if the valves were really being hit by the pistons.
Last edit: 26 Oct 2011 00:22 by loudhvx.

Please Log in or Create an account to join the conversation.

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Could use some timing help, New guy here....

26 Oct 2011 01:01
#485389
I may go ahead and pull it, but teh valves were hitting each other, Not the piston's. With them hitting the piston i would have stopped before ruining them. but with them hitting each other, I was barely turning and it felt just like it was about to pop over when I heard the clunk and she did turn over. I am thinking it was just barely tapping each other.


Do you guys think i need to order another head gasket, or will i be able to reuse this one?

Please Log in or Create an account to join the conversation.

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Could use some timing help, New guy here....

26 Oct 2011 01:03
#485390
And again, there is NO "T" mark anywhere at all on the crank. And I DID already down load the manual. I Know its thr right manual, but it is wrong for my engine. :shrug:

Please Log in or Create an account to join the conversation.

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Could use some timing help, New guy here....

26 Oct 2011 01:36
#485393
Alrighty, YOU guys are awesome! That link to your page loud is priceless! That sir is the BEST info on the web about these engines and does NOT come up in ANY search engine. I have both cams setting at exact timing, KNOW how to install them, AND know about teh tensioner when i did NOT before, All in ONE site. Gotta say, this MAY become my second fav forum!! I am a chapter leader on my truck forum...so can't be biased..lol. Gotta say, PLENTY to read on that page.


BTW, checked and I can not for the life of me find that "T" anywhere! crank, crank cover, ANY cover, hell i even checked the bolt head itself by scapping off the "Paint" lol. mind a pic showing where I should be looking?

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: Could use some timing help, New guy here....

26 Oct 2011 03:03 - 26 Oct 2011 03:25
#485402
The T mark is on the advancer mechanism for the ignition. It is under the timing plate, which is under the small cover on the right side of the engine. Depending on what bike the motor is out of, it may look different, but if you check this link: home.comcast.net/~loudgpz/GPZweb/Ignitio.../PickupAndRotor.html

and scroll about 2/3 of the way down, you'll see an image of what the advancer looks like for a mechanical-advance bike. The Most of it will be covered up by the timing plate though. You have to look through the small oval window at the top of the timing plate. You should see a small pointer cast into the engine casing.

If the bike has no ignition parts, then you will have to find TDC the old fashioned way... take off the alternator cover. That is the big round cover on the left side of the engine. There you will see the flywheel. Put a vise grip on the bolt at the center of the flywheel. You are using a vise grip so there is no slop in the movement. Put a screwdriver into a spark plug hole on #1 cylinder (left most cylinder). Now rotate the crank forward (same direction as the wheels) until the screwdriver reaches the top of travel. If you meet with mechanical resistance, stop, you have to find out why (valves hitting etc). You'll notice if you rock the vise grip back and forth very slowy over TDC, the piston will stop moving as you approach the top, from both directions. Put a mark on the flywheel at the point where the piston stops moving as you rock the vise grip from each direction. There will be two lines. One for each direction. The middle of those two lines is TDC.

Cool 4-wheeler, by the way! That motor is probably one of the LTD or Spectre motors. They have more grunt than the gpz motors, which should be great for mud and stump pulling.
Last edit: 26 Oct 2011 03:25 by loudhvx.

Please Log in or Create an account to join the conversation.

  • Banditz
  • Banditz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 26
  • Thanks: 0

Re: Could use some timing help, New guy here....

26 Oct 2011 04:57
#485415
Well dang, never thought to look under there. I already did the TDC by removing the plug. heck I thought about doing that first thing..Just didnt know if it HAD to have that T at the top or not. Wasnt sure if it could be at TDC with that T at the bottom or not...Was worried about that. LOL I already have that small cover off so I will take a look under it to make sure the T is at the top now...

As for the Motor, no...its the baby one. LOL I do not have the grind ring things on the cam. BUT she is still PLENTY fast enough. Will make you scared to go faster for sure..I hit 78 on her when I first blew out the gasket. Tellin ya now, if the head gasket is weak, a high speed pass will take her out fast! Now I am just worried about the valves. Worse case i guess i have to replace them. but really not wanting to put money into this engine when I can find a much newer engine off craigslist. What about the head gasket? think if I must take off the head I can do it and reuse the head gasket? Those things are so high dollar I sure don't wanna buy another. It's brand new and the engine hasnt been ran of course..

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Could use some timing help, New guy here....

26 Oct 2011 09:25 - 26 Oct 2011 10:02
#485427
You should post up the # that is on the engine case, so it can be found out as to which yer you have. If those are the correct original carbs for the motor, then its probably an 83 year engine.
Here you can get a Top gasket set for cheap: www.z1enterprises.com/Gasket-Set--Kawasa...Topend-Set-1736.aspx
But you need to find out what else may now be a problem. the Valves it hitting each other, would be bent. Do a Compression & Leak Down test to determine if this has happened. Timing must be corrected first. Also if you had the tensioner fully installed with wedge when putting on the valve cover, you may have broken the chain/ guides/ etc. Or maybe you had a link of the chain kinked up under the crank on the bottom sprocket, and it Popped straight. Better find out before putting power to it, if there is a problem, it will show up when running, if it runs/ long.
Get the # off of the Motor and post it up/ add it into your profile signature.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 26 Oct 2011 10:02 by Motor Head.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum